Twin Channel 4 Pin Cables for reversing and rear view cameras

Twin Channel 4 Pin Cables for reversing and rear view cameras

Our selection of twin signal 4 pin cables for reversing cameras.  Typically used where you have multiple signals from cameras being run to the front of the vehicle.

5M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB05Y

5M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB05Y

CAB05Y-SD
  • Our 5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£11.00

VAT Included £1.83
View/Buy
10M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB10Y

10M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB10Y

CAB10Y-SD
  • Our 10M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£16.00

VAT Included £2.67
View/Buy
10M (with 8mm link) - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB10Y-8mm

10M (with 8mm link) - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB10Y-8mm

CAB10Y-8mm-SD
  • Our 10M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£17.00

VAT Included £2.83
View/Buy
12.5M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB12Y

12.5M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB12Y

CAB12Y-SD
  • Our 12.5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£18.50

VAT Included £3.08
View/Buy
12.5M (with 8mm link) - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB12Y-8mm

12.5M (with 8mm link) - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB12Y-8mm

CAB12Y-8mm-SD
  • Our 12.5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£19.50

VAT Included £3.25
View/Buy
15M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB15Y

15M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB15Y

CAB15Y-SD
  • Our 15M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£21.00

VAT Included £3.50
View/Buy
15M (with 8mm link) - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB15Y-8mm

15M (with 8mm link) - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB15Y-8mm

CAB15Y-8mm-SD
  • Our 15M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£22.00

VAT Included £3.67
View/Buy
20M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB20Y

20M - Twin 4 Pin Aviation Screw Connector Extension Cable for 2 reversing cameras | CAB20Y

CAB20Y-SD
  • Our 20M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
  • We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
  • Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
  • Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
  • The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
  • This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
  • This cable is sometimes known as a 4 pin aviation connector cable.

£26.00

VAT Included £4.33
View/Buy

Twin Channel 4 Pin Cables for reversing and rear view cameras

All of our reversing camera extension cables are made by one cable manufacturer who we have a very good log history with. We specify that all of our cables are made to 5mm thickness, with a foil outer shielding, and pure copper cores/shielding. A lot of cable on the market use copper coated aluminium (CCA), or copper coated steel (CCS), which make them more easily damaged, and more readily degrade over time - giving reduced image quality.